Things You Should Keep In Mind Before Installing A Fence

The first thing to do is tell the neighbors that you plan to build a fence. An unexpected fence is the first salvo in many neighborhood wars.

After notifying neighbors, you need to find out two things:

  1. Where are the boundaries of your property, and
  2. Underground communications are laid (gas, electricity, telephone, cable).

You may be able to find stakes or “monuments” that are used to mark the corners of your lot (a metal detector helps), but if not, your city or county government can sometimes help. They will have lot maps or other documents that legally describe your property. You must have the entire fence, including the supports around the posts, within the boundaries of your property. Hire a surveyor if necessary.

In most areas, utilities will mark their cables and pipes on the ground if you ask them to. Keep at least 18 inches away from the marks. Or, better yet, call before you dig.

Check with your local building authority to see if the building code governs fences. Often the code requires the best side of the fence to be facing outward, towards the street or neighbors (which is a surprise, isn’t it?). There may also be restrictions on the height of the fence or how close you can be to property lines (called “retreat”).

Designate your fence

Once you know the legal requirements, set up stakes and rope to mark the location of your fence posts. The strings must be at least 6 inches inside your property lines. Map your fence on graph paper, indicating the length of each section.

Now calculate how far apart the posts will be for each section of the fence. Poles must be 8 feet. Apart or less, from the center of one pillar to the center of the next. Here’s how to calculate it:

  • Take the total section length in inches and divide by 96.
  • Take that number and round up to the next highest whole number.
  • Divide the total length of the railing section by this number.
  • The result is the center distance.

If you need a gate, decide on its location. It should be as level as possible, and the loop should be downhill. The opening for the gate should be a multiple of the width of the fence board plus 3/4″ (Fig. C).

Mark the location of the posts and gates and the distance between the centers of the posts on the fence map.

Custom Materials

Using the fence map as a guide, order lumber, concrete, and fasteners. The fence merchant will have the best selection of lumber.

If you mix concrete yourself, figure about two for 80 pounds. Mail bags. Otherwise. The figure is approximately 1 yard of concrete per 40 posts.

Choose aluminum. Stainless steel nails or hot dip galvanized (not galvanized) nails to minimize the formation of rust spots. Hot-treated nails can be recognized by their rough texture.

Installation of corner posts

The first step in building a fence is to install posts at the ends and corners of the fence. The posts must be deep enough: 32 inches deep is the minimum for a 6-foot high fence.

Start by digging holes for the pre-cut corner and end posts. The ropes and stakes mark the fence’s location right inside the boundaries of your property.

Adjust the uprights to be at the correct height above the ground. Either by tamping excess dirt into the bottom of the hole or by deepening it. Remember that such a fence with pre-cut decorative tops must have the posts set to the correct height. To other fences. For example. Those with messages that are nailed with caps or tips.

A lot can happen between when an idea first hits somebody’s head about needing new fences for their property up until they’ve got one built on-site at home; but no matter what type or style it may be (wooden picket? Metal paneling), if there was ever going ́to get accomplished by the way out this project then we’re here ready with expertise like yours.

Why Replacing Old Fence is a Good Idea?

Replacing an old fence is a great idea for many reasons. The first and most obvious reason is that it’s a cost-effective solution. Replacing an old fence is much cheaper than hiring a professional to do it, and it can be done in a shorter time frame. You also don’t have to worry about the quality of the fence- you can choose any type of fence you like. Additionally, if you don’t have an existing fence, you can find one similar in design to your current fence and replace it for a fraction of the cost.

How to replace an old fence

Free stock photo of balloons, birthday party, careReplacing an old fence is a simple process that can be done shorter than hiring a professional. You simply need to find a similar fence in design to your current fence and replace it for a fraction of the cost. Additionally, if you don’t have an existing fence, you can find one similar in design to your current fence and replace it for a fraction of the cost.

Replacing an old fence with a better quality

Replacing an old fence with better quality is another key benefit of replacing an old fence. By upgrading your fence to better quality, you’ll help protect your property from damage and make it easier to maintain. You can also choose a more durable fence that will last longer. Better fences can help deter burglars and thieves from entering your home.

Tips for Replacing an Old Fence.

You can follow a few simple tips to replace an old fence. First, research the different types of available fences and choose the most appropriate one for your needs. Next, find a contractor who can help you with the installation. Once the fence is replaced, be sure to maintain it to ensure that it continues to meet your expectations.

Contact True Built Fencing, a fence contractor in Austin TX, and let professionals build your perfect fence.

Company Name
True Built Fencing
Phone
+1 (512) 354 1601
Address
2025 Guadalupe Street, Suite 250
City
Austin
State
TX
Postal Code
78705
Country
United States
Website
https://truebuiltfencing.com/
Google my Business Website
https://true-built-fencing-austin.business.site/
Google Site
https://sites.google.com/view/true-built-fencing-austin/